HOT AIR UNIVERSAL OVEN (Memmert Type) 6701
Three side heating elements. Standard double wall fabrication. Inner chamber made of richly anodized aluminium or highly polished stainless steel sheet. Exterior fabricated out of thick mild steel sheet duly finished in stoved enamel off-white paint or paste mat finish colour combinations. The gap between the walls is filled with-special grade glass-wool for heat insulation. Inner chamber is ribbed for placing shelves at convenient levels. Provided with two or three removable shelves. special elegant door closing device has been provided. Nichrome wire heating elements provided on three sides attain quick and uniform heating in range of 50ºC to 250ºC ±1ºC controlled by capillary type thermostat. L-shaped thermometer is built-in type. Control panel is provided with selector switch of high or low rates of power, thermostat control knob and indicators for mains & thermostat. Supplied with cord and plug. The equipment is suitable to operate on 220 Volts 50Hz, single phase AC. Chamber size in mm:
a) 300x300x300
b) 275x400x275
c) 350x350x350
d) 400x400x400
e) 450x450x450
f) 600x450x450
g) 600x600x600
h) 900x600x450
I) 900x600x600
j) 900x900x900
OPTIONALS : (Extra Cost)
i) Air circulating fan.
ii) Timer 0-24 hours.
iii) Digital temperature Indicator.
iv) Digital temperature indicator-cum-Controller.

DRYING OVEN 6704
Double wall extra sturdy construction on thick angle iron frame with both inner and outer walls of thick PCRC sheet duly protected against rusting and corrosion. The exterior is finished in ash-grey hammer tone. The gap is filled with special grade glass wool for heating insulation. A heavy duty constantly running blower provided to maintain uniform constant temperature in the chamber. Front door mounted on heavy hinges is double walled. Temperature is controlled by a capillary type thermostat with range from 50ºC to 250ºC ±2ºC to 3ºC workable on 220Volts, 50Hz, single or three phase AC. Provided with two trays. The panel provided with mains indicator, heater indicator, temperature control knob and dial type thermometer, Cord and plug.
Chamber sizes in mm.
a) 900x600x600, b) 1200x900x600, c) 1500x90x600, b) 1800x1200x900.
Note: Size of above equipment of your requirement can be fabricated on demand.
OPTIONALS: (Extra Cost)
i) Timer 0-24 hours.
ii) Digital temperature indicator.
iii) Digital temperature indicator-cum-controller.

TRAY DRYER 6706
Standard sturdy double wall fabrication. Inner & outer chambers made of thick mild steel sheet. Inner chamber baked silver paint finish and exterior finished in hammer tone. Gap between two walls filled with glass wool for temperature insulation. Heavy duty forced air blowers are provided to constantly circulate hot air to achieve uniform temperature in the whole chamber. Double wall door is mounted on heavy hinges and provided with heavy moulded latch. Temperature is controlled by a thermostat and it can be read on dial type thermometer.
Temperature Range: 50ºC to 25ºC ±2ºC to 5ºC and equipment is workable on 220Volts, 50Hz, Single Phase or 440 Volts AC supply.
a) For 12 trays of 390x780x30 approx.
b) For 24 trays of 390x780x30 approx.
c) For 48 trays of 390x780x30 approx.
d) For 96 trays of 390x780x30 approx.
e) For 192 trays of 390x780x30 approx.
OPTIONALS : (Extra Cost)
i) Timer 0-24 hours.
ii) Digital temperature indicator.
iii) Digital temperature indicator-cum-controller.
Note: Dryers for other sizes of trays available on demand.

BOTTLE DRYER 6709
Standard specifications as model 6704 and 6704 Complete with thermostatic temperature control, dial type thermometer, double wall construction and two side opening doors. Temperature attained uniformly by forced air circulation through heavy duty blowers.
a) For 8 crates of size 440x370x150 approx.
b) For 10 crates of size 440x370x150 approx.
c) For 12 crates of size 440x370x150 approx.
OPTIONALS : (Extra Cost)
i) Digital temperature indicator.
ii) Digital temperature indicator-cum-controller.
iii) Timer 0-24 hours.

OVEN/DRYER, MULTIPURPOSE 6710
Body specification as above but without forced air circulation which can be provided against extra cost, if required. temperature thermostatically controlled with range from 50ºC to 250ºC workable on 220 Volt AC 50Hz single phase. Chamber size in mm:
a) 1800 x 900 x 900
b) 1950 x 975 x 975
c) 1950 x 1350 x 975
d) 1950 x 1200 x 1200
OPTIONALS : (Extra Cost)
i) Forced air blowers.
ii) Digital temperature indicator.
iii) Digital temperature indicator-cum-controller.

OVEN VACUUM 6714
Double walled construction. Inner round chamber made out of stainless steel. Exterior made out of mild duly finished in stoving enamel white paint. Gap between the two filled with glass wool for temperature insulation. Temp range 50ºC to 150ºC ±3ºC. the body capable of with standing vacuum of 760mm Hg. Complete with temperature regulator, indicator lamp, on-off switch , cord & plug. Workable on 220Volts AC 50Hz single phase. Chamber size in mm. (dia x depth)
a) 250 x 300, b) 300 x 300, c) 300 x 500
OPTIONALS : (Extra Cost)
i) Digital temperature indicator.
ii) Digital temperature indicator-cum-controller.
iii) Vacuum pump.

INCUBATOR BACTERIOLOGICAL (Memmert Type) 6716
Double wall fabricated. Inner chamber made out of richly anodized aluminium or highly polished stainless steel sheet and outer made out of thick mild steel sheet finished in white stoving enamel paint or mat finished paste colour combinations. The gap is filled with special glass wool. Double wall door with double glass window for observation in the chamber. Temperature range 5ºC above ambient to 80ºC ±2ºC controlled by a thermostat. L-shaped thermometer is provided for taking temperature reading. Panel is provided with pilot lamps for main heaters, On-Off switch, temperature Control knob etc. The equipment workable on 220Volts AC 50 Hz single phase. Heating is achieved from 3 sides.
Perforated removable shelves also provided. Chamber sizes in mm.
a) 300 x 300 x 300
b) 350 x 350 x 350
c) 400 x 400 x 400
d) 450 x 450 x 450
e) 600 x 450 x 450
f) 600 x 600 x 600
g) 900 x 600 x 450
h) 900 x 900 x 900
Note: Sizes of your choice can be fabricated on demand.
OPTIONALS: (Extra Cost)
i) Air circulating fan.
ii) Timer 0-24 hours.
iii) Digital temperature indicator.
iv) Digital temperature indicator-cum-controller.

INCUBATOR (Bio-Chemical Oxygen Demand) 6720
Designed for low temperature incubation and routine determination of Bio chemical oxygen demand (B.O.D). Double wall construction. Inner chamber made of richly anodized aluminium or highly polished stainless steel sheet with self supports for wide range of shelf spacing. Supplied with two/three removable perforated shelves. Exterior made of thick mild steel sheet duly finished in white stoving enamel paint or paste mat finish colour combinations. Outer double wall door is provided with magnetic gasket and lock & key arrangement. Inner door made out of a clear acrylic sheet allowing inspection of material in the chamber without disturbing the chamber temperature. Door operated inner illumination has been provided. The gap between walls of equipments are filled with glass wool for insulation. The cabinet is mounted on castors. Temperature is controlled by a sensitive thermostat from 5ºC to 50ºC ±1ºC. For lower temperature working a standard cooling unit with a sealed compressor with protective devices has been provided below the chamber for safe and efficient working. Heating arrangement has been made within the chamber for higher temperature working. The temperature can be regulated within the range by means of high precision double action thermo-regulator. Inner air circulating system is provided to achieve uniform temperature in the whole chamber. A control panel is provided with various indicators, On-Off switch, L-shaped thermometer. Supplied with cord and plug. The equipment is workable on 220Volts, 50Hz single phase AC. Inner Chamber sizes in mm:
a) 610x455x410
b) 825x500x415
c) 865x565x565
d) 900x650x575
OPTIONALS : (Extra Cost)
i) Digital temperature controller-cum-Indicator.
ii) Timer 0-24 hours day night cycle.
iii) CO2 air mixture intel nozzle.
iv) Humidity system by spray or injection methods.
v) Audio Visual alarm.
vi) Automatic Voltage stabilizer 3KVA. (must)

ORBITAL SHAKING INCUBATOR 6723
a) Standard double wall construction. Outer chamber made out of mild steel finished in stoving enamel paint. Inner-chamber made of stainless steel sheet. The double door provided with double glass full view window. Interchangeable platform has been provided. temperature range 5ºC above ambient to 60ºC ±2ºC is controlled by a solid state electronic controller. Variable speed control regulator controls the speed up to 200 rpm. Supplied complete to work on 220Volts 50 Hz single phase AC . Capacity: 16x500ml conical flasks.
b) Same as above but temperature range 10ºC to 50ºC with light arrangement.

SEROLOGICAL WATER BATH 6725
Double wall construction, inner being made out of highly polished thick stainless steel and outer made out thick mild steel sheet finished in stoving white enamel paint or staple mat colour combinations. The gap is filled with special glass wool for temperature insulation. The bath is provided with a drain cock to easily drain out the water and clean the chamber when required. A pyramidal shaped cover is provided. Immersion type heating elements are fitted at bottom. temperature range 5ºC above ambient to 80ºC with accuracy ±0.5ºC to 1ºC is controlled by capillary thermostat regulated by a graduated knob on the panel, which is also provided with pilot lamp etc. The equipments is workable on 220Volts, 50Hz single phase AC. The baths are supplied without thermometer and stirring arrangement. Working chamber sizes in mm (Stainless Steel)
a) 300 x 175 x 175
b) 300 x 250 x 175
c) 375 x 300 x 175
d) 450 x 300 x 175
OPTIONALS: (Extra Cost)
i) Stirring arrangement with S.S. rod and blades.
ii) Digital temperature indicator.
iii) Digital indicator-cum-temperature controller.

WATER BATH RECTANGULAR (Thermostatic Control) 6727
Standard double wall construction, inner being stainless steel outer of mild steel duly stoving paint finish and gap filled for temperature insulation with special grade glass wool. top cover with 75mm holes with concentric rings. temperature range 5ºC above ambient to 95ºC controlled by a thermostat. Heating is attained by an immersion type element with accuracy of ±1ºC. Supplied complete with plug & cord. Panel provided with pilot lamps, thermostat control knob etc. Models: a) 5 holes, b) 6 holes, c) 12 holes

WATER BATH RECTANGULAR (SINGLE WALL) 6729
Body made out thick stainless steel. top made out of chrome plated sheet. Concentric rings to cover 3” dia holes are provided. Heating elements have automatic cut-off device which operates when the bath gets dried. Equipment working on 220Volts Hz single phase AC.
a) 6 holes
b) 12 holes
OPTIONALS : (Extra cost)
I) Digital temperature indicator.
ii) Digital temperature indicator-cum-controller.

WATER BATH PRECISION (CONSTANT TEMPERATURE CONTROL) 6730
Construction as per model 6729 but with glass windows on both opposite sides, for observation. temperature controlled by mercury contact thermometer with a sensitivity of 2ºC. Suitable for precision laboratory activities requiring constant temperature with high degree of accuracy. Complete with stirrer with speed control regulator workable on 220Volts Hz single phase AC. Chamber Size in mm
a) 425x250x225
b) 450x375x375
c) 600x450x450

WATER BATH PARAFFIN 6731
Body specification as per standard double wall water baths but provided with cups and sleeves for glass tubes. Models:
a) 4 cups & 6 sleeves.
b) 6 cups & 8 sleeves.
c) 12 cups & 14 sleeves.

WATER BATH TISSUE FLOTATION 6734
Suitable to spread wax section ribbons after microtomy to get wrinkle free specimen for staining. Double wall round construction. Inner chamber black anodized aluminium and outer made out of mild steel duty finished in stoving white enamel paint. Inner chamber is single stainless pieces to avoid chances of any leakage with enough wide rim for drying wet slides. temperature range 5ºC above ambient to 70ºC ±2ºC. Immersion type heating elements attain the controlled temperature regulated by a capillary thermostat. Panel provided with thermo-regulator knob, pilot lamp and is supplied with cord & plug. equipment workable on 220Volts Hz single phase AC. Chamber sizes in mm & inches: a) 200x75, b) 250x125

OIL BATH (High temperature) 6736
Stainless Steel, Double wall construction. Inner chamber made of highly polished stainless steel or copper sheet and outer made of mild steel duly finished in stoving enamel. Temperature range 50ºC to 250ºC ±2ºC is controlled by a thermostat. The oil bath is suitable for a wide range of applications like oxidation stability test on oils, other tests in which high temperature control is required. Supplied complete with stirrer, diffuser shelves, cover etc. panel provided with On-Off switch, pilot lamps thermostatic control knob etc. Chamber size in mm :
a) 250x250x250
b) 300x300x250
c) 350x250x250
OPTIONALS: (Extra Cost)
i) Mercury contact thermometer and relay with accuracy better than 1ºC.
ii) Digital temperature indicator.
iii) Digital temperature indicator-cum-controller instead of thermostatic control and L-shaped thermometer.

OIL BATH (High temperature) 6737
As above, but with well type round body.

UNIVERSAL WATER BATH (Dual Purpose) 6738
Useful for dual purpose. It is a combination of serological and routine rectangular water bath with holes and co-centric rings. Standard double wall construction. Inner chamber made out highly polished stainless steel sheet and exterior made out of thick mild steel duly finished in stoving enamel paint, The gap between the two walls is filled with special glass wool for temperature insulation. Immersion heaters are provided for heating to attain temperature range from 5ºC above ambient to 90ºC ±1ºC ans is controlled by capillary type thermostat, controlled by thermostat knob on the panel. Supplied complete with plug & cord. The equipment works on 220Volts 50Hz single phase AC. Equipments has been provided with two covers, one of a pyramidal shape and the other with 75mm diameter holes with co-centric rings. The chamber is provided with drain cock to easily drain out the water whenever required. Chamber sizes in mm
a) 300 x 225 x 175
b) 450 x 300 x 175
OPTIONALS : (Extra Cost)
i) Stirring arrangement SS rod & blades.
ii) Digital temperature Indicator.
iii) Digital temperature Indicator-cum-controller.

CONSTANT TEMPERATURE REFRIGERATION LIQUID BATH 6740
a) Standard double walled construction. Inner chamber made out of thick highly polished stainless steel sheet. Temperature range 5ºC to 90ºC and controlled by sensitive Mercury contact thermometer with an accuracy of ±0.2ºC. Fitted a stirrer and speed regulator. Chamber size : 500 x 250 x 250mm.
b) As above but refrigerated bath fitted with a FHP pump for circulating the cord liquid to the external equipment.
OPTIONAL: (Extra Cost)
i) Digital temperature controller-cum-indicator instead of contact thermometer.

REFRIGERATED LIQUID BATH 6741
Standard construction, inner chamber made out of stainless steel sheet with digital temperature controller-cum-indicator. Temperature control range from -20ºC to 20ºC. Chamber Sizes : 450 x 300 x 300 mm.

WATER BATH INCUBATOR SHAKER 6743
(Metabolic Shaking Incubator)
Useful for studies on tissue metabolism, enzymes and protein coagulation and other experiments demanding shaking at constant speed under controlled temperature conditions. Double walled construction, inner chamber made out of thick highly polished stainless steel sheet and outer made out of thick mild steel duty finished in stoving enamel paint. The lid made of stainless steel. The gap between the two chambers filled with glass wool to pre vent loss of heat. The temperature is achieved by superior immersion heater and is controlled by capillary type thermostat from ambient to 90ºC ±0.5ºC. The shaking mechanism is fitted with variable speed motor coupled to shaking tray work in on rollers. Shaking speed is controlled from 40 to 140 cycles per minute. Shaking tray can hold either test-tubes or flasks of 25ml. or 50ml. or 100ml. capacity. Front panel includes on-off switch, shaking mechanism indicator, speed control, thermostat control etc. L-Shaped thermometer is provided to indicate inside temperature. Equipment to work on 220Volts, 50Hz single phase AC. Inner chamber sizes in mm: a) 275 x 275 x75, b) 275x275x150, c) 400x300x75
OPTIONALS : (Extra Cost) Shaking Tray for 25ml, 50ml and 100ml

WATER STILL (Manesty Type) 6750
Aluminium Wall hanging casted aluminium vessel is electrically operated for getting pyrogen-free distilled water automatically. Wall hanging space saving arrangement is provided. The condenser is seamless. Fitted with automatic ejection device which operates automatically when water vessel gets dried. The baffle cup and condenser are made out of thick stainless steel sheet. Output Capacity Per Hour approx. a) 2-3 litre, b) 4-5 litre

WATER STILL (Manesty Type) 6753
Stainless Steel Wall hanging. Specification as above but made of stainless steel sheet.
Output Capacity per hour approx.
a) 2-3 litre, b) 3-4 litre, c) 4-5 litre

WATER STILL (BARNSTEAD TYPE) Table model 6755
Double wall construction having both made out of highly polished stainless steel sheet. The gap between the two is filled with glass wool for heat insulation. It is easy to handle table model working on 220 Volts, 50 Hz single phase AC.
Output Capacity per hour (Approximately)
a) 4-5 litre, b) 8-9 litre, c) 15-16, d) 25-26 litre

DOUBLE DISTILLATION STILL 6756
Stainless steel, output approximately 6-8 litres per hour of double distilled water.

RECTANGULAR MUFFLE FURNACE (Laboratory Model) 6760
Outer shell out of thick mild steel duly finished in attractive stoving enamel paint. Fitted with grooved refractory for supporting the heating elements made out of kanthal wire and are easily replaceable. Maximum temperature 1000ºC with working temperature 940ºC controlled by energy regulator. Complete with indicators, pyrometer, thermocouple - thermal fuse etc. workable on 220 Volts, 50 Hz single phase AC. Inner Muffle size in mm
a) 225x100x100
b) 250x125x125
c) 300x125x125
d) 300x150x150
e) 300x200x200
f) 350x175x125
g) 475x175x125
h) 450x225x225
OPTIONAL : (Extra Cost) Digital Temperature indicator-cum-controller instead of energy regulator and pyrometer.

MUFFLE FURNACE (Industrial) RECTANGULAR 6762
Specification as model 6760 but maximum temperature 1150ºC with working temperature 1100ºC. Complete in all respects as above. Inner muffle size in mm
a) 225x100x100
b) 300x125x125
c) 300x150x150
d) 300x200x200
e) 450x225x225
OPTIONAL: (Extra Cost)
Digital temperature indicator-cum-controller instead of energy regulator & pyrometer.

MAGNETIC STIRRER 6770
Compact stirring device utilizing a rotating magnetic field applied from below the container. The stirring is accomplished by a Teflon rotor placed in the liquid to be stirred. Complete with pilot lamp, plug cord, continuously variable speed regulator. The body is made of mild steel duly finished in stoving enamel and mounted with stainless steel top which serves as a hot plate. Stirring and heating units are properly insulated. In model with heating system temperature is controlled by a energy regulator. An electronic speed controller is also provided. The equipment works on 220V AC 50Hz single phase.
a) Magnetic stirrer with hot plate. Capacity: 1Lt. 2Lt, 5Lt., 10Lt.
b) Magnetic stirrer without heating system. Capacity: 1Lt, 2Lt, 5Lt, 10Lt
c) Magnetic stirrer with hot plate & energy regulator. Capacity: 1Lt., 2Lt, 5Lt, 10Lt, complete with Teflon coated magnet.

LABORATORY STIRRER 6775
Heavy & stable cast iron base duly painted with mild steel chrome plated upright rod. AC/DC motor with stainless steel stirring shaft and blades, variable speed control unit provided. 1/20 HP motor provided for smooth longtime stirring. Height of stirrer and stirring space adjustable. To work on 220 Volts 50 Hz single phase AC.

TISSUE HOMOGENISER 6778
Heavy stable cast iron base duly painted with mild steel chrome plated upright provided with strong adjustable clamps to hold motor with stirring rod of stainless steel with Teflon grinder and clamp to hold tissue homogenising vessel of borosilicate glass which is also adjustable. Speed variable through a control unit to work on 220 Volts, 50 Hz single phase AC. Motor used is of 1/20 HP
a) Homogenising Vessel 25ml.
b) Homogenising Vessel 50ml.
c) Homogenising Vessel 100ml.

HEATING MANTLES 6780
Body in made of one piece aluminium ans is logged with special mineral wool. The panel is provided with on-off switch, energy control knob, pilot lamp. etc. Provided with joint less hand knitted heating nets of glass yarn capable of with standing high temperature up to 400ºC. Single individual size up to 5 liters capacity containers are available. Supplied complete with cord & plug to work on 220 Volts, 50 Hz single phase AC. Single circuit system has been adopted. Single size x Wattage
a) 50 ml.x60
b) 100 ml.x60
c) 250ml.x150
d) 500ml.x200
e) 1 Lit.x300
f) 2 Lit.x 450
g) 3 Lit.x450
h) 5 Lit.x600
Note: Other sizes, capacities, multiple models and spare heating mantles can be offered on demand.

HOT PLATES 6785
Laboratory hot plates are available in round and rectangular shapes. Body is fabricated out of thick mild steel sheet duly finished in stoving enamel paint. The hot plate made of cast iron, nicely & precisely machined & smoothed duly finished in heat resistant black paint is firmly mounted on the body. Heavy duty heating elements are securely laid under the plate to operate on 220Volts, 50 Hz single phase AC. Temperature is controlled by a three heat rotary switch along with an indicator lamp for the mains and cord & Plug
A) HOT PLATE ROUND Single. Specification as above with 200 mm. dia. moulded top.
B) HOT PLATE ROUND Double. As above but with two plates of 200mm dia. having independent pilot lamps & switches.
C) HOT PLATE Rectangular. Specification as above but plates is rectangular in shape.
Following standard sizes are available:
i) 30x250mm
ii) 40x250mm
iii) 45x300mm
iv) 60x450mm
Note: Other sizes can be offered on demand.
OPTIONALS : (Extra Cost)
a) Energy regulator.
b) Digital temperature Indicator-cum-Controller.

SLIDE WARMING TABLE 6788
A versatile equipment to heat slides with fresh microtomed sections to attain maximum flatness before staining. Temperature range ambient temperature to 70ºC i.e. below the melting point of wax. the temperature is thermostatically controlled. The body is made out of thick mild steel duly finished in stoving enamel and top is made of highly polished copper or stainless steel sheet. Complete with thermostatic control knob, indicator lamp, plug & cord etc. To work on 220Volts, 50Hz single phase AC. Standard sizes available.
a) 300x250mm
b) 400x250mm.
c) 450x300mm

ROTARY SHAKER (VDRL Rotator) Fixed Speed 6790
Suitable for VDRL and other agglutination tests, blood grouping tests and for mixing of solutions in small flasks, beakers or bottles. Body made of sturdy mild steel sheet duly finished in stoving enamel paint. Tray type platform size 300x300mm can take cavity slides, bottles, flasks etc. for shaking at a fixed speed, by the help of spring wires. Standard fixed speed 180 RPM. An automatic 60 minutes timer can be provided against extra cost as optional by which shaking duration can be set to work on 220Volts, 50 Hz single phase AC.
NOTE: Variable speed rotator can be offered on demand.
OPTIONAL : (Extra Cost) 0-60 minutes timer.
SHAKING MACHINE (Wrist Action) 6794
Heavy cast - iron base with sturdy construction with two side arms for holding flask. A heavy duty fractional motor with variable speed through continuously variable speed
controller is provided. The holders can hold flasks of capacity 100 to 1000ml. Supplied complete with cord & plug etc. to work on 220 V AC 50 Hz single phase. Speed 80-280 oscillations per minute.
a) Model to hold 4 flasks.
b) Model to hold 8 flasks.
c) Model to hold 16 flasks.
OPTIONAL:
Automatic 0- 60 minutes timer.

VORTEX SHAKER (Test Tube Shaker) 6796
Useful for accelerated mixing of solutions in test tubes, small flasks or centrifugal tubes etc. The housing is 150x150 mm. the speed is regulated by a speed control device. Short eccentric stroke motor imparts vigorous agitation to the tubes or flasks. Body is strong and finished in stoving enamel paint. The equipment is workable on 220Volts, 50 Hz, Single phase AC.

SHAKING MACHINE (KAHN Rack Type) 6797
Designed for shaking kahh racks, bottles, flasks of different sizes by adjusting compartments. Fitted with heavy duty motor to work on 220 Volt AC 50Hz single phase. the rate of motion is adjustable mechanically by belt tension. Speed is fixed in same models to approx. 275 or variable as detailed below.

	Size of Carrier	Stokes oer Minute	Motor	Body Type
(a)	500x330x100	275	0.25 HP	Open
(b)	500x330x100	275	0.25 HP	Covered
(c)	500x330x100	150 to 250	0.25 HP	Open
(d)	790x430x100	150 to 250	0.25 HP	Covered
(e)	915x460x100	150 to 250	0.50 HP	Covered

OPTIONAL (Extra Cost) 0-60 minutes timer.
Shaking machines of other specification can be offered on demand.

ROTARY SHAKER (Platform type) 6798
Body made out of thick mild steel sheet finished in stoving enamel paint. Heavy duty motors of suitable capacities are provided for long time, continuous operation. Fixed speed and variable speed models are offered. Platform is provided with rubber discs to hold flasks. To work on 220 V AC 50 Hz single phase. The choices available are:

	Platform Size	Holding Capacity	Motor
(a)	450x450mm	25 flasks of 100ml	0.25 HP
(b)	450x450mm	36 flasks of 50ml	0.25 HP
(c)	450x450mm	15 flasks of 250ml	0.25 HP
(d)	550x550mm	25 flasks of 250ml	0.25 HP
(e)	650x650mm	36 flasks of 250ml	0.25 HP
(f)	1000x1000mm	81 flasks of 250ml	1 HP
(g)	1000x1000mm	81 flasks of 500ml	1 HP

Other sizes & capacities can be offered on demand.
OPTIONALS (Extra cost) 0-60 minutes timer.

MELTING POINT APPARATUS 6804
A metallic heating block is provided with holes to receive three capillary tubes and a stem type thermometer. The body is finished in stoving enamel paint. The apparatus can measure melting point up to 350ºC. the block is heated by superior heating elements and temperature is controlled by a heat regulator. A shadow less lamp has been provided to illuminate the capillaries and a focusable magnifier facilitates in observations. The whole unit is housed in a aluminium cast casing and provided with a control panel. Provided with indicator lamps, heat energy regulator, on-off switch, cord-plug etc. The equipments is to work on 220 V AC 50Hz single phase. Supplied without thermometer & capillaries.
OPTIONALS: (Extra Cost)
i) Thermometer 360ºC.
ii) Capillary tube set.
iii) Cooling plug.

PIPETTE WASHER (Automatic) 6810
It constitutes of a washing cylinder made of stainless steel sheet highly polished
measuring 63 cm. in height and 15 cm. in diameter and is mounted on a base of 26 cm. diameter. It is provided with a removable pipette holder. It can accommodate pipette of 37.5 cm length. It works on the siphoning principle.

CENTRIFUGE MACHINE, HAND 6812
A single speed hand driven machine consisting of dies casted parts and a steel pinion and worm drive. Screw clamps the machine to the bench. Finished in white color, with removable crank handle. Suitable for 15ml. glass tubes. For 2 Tubes For 4 Tubes

MEDICO/CLINICAL CENTRIFUGE 6814
Electrically operated, dome type, sturdy, stable heavy body with resiliently mounted motor working on 220 Volts, 50 Hz, single phase AC for vibration free performance with built in 5 speed regulator and a non-removable swing out rotor. Complete with tube carriers. Maximum speed 3500 RPM. Neatly finished in stoving enamel paint.
a) 4x15 ml. tubes.
b) 6x15 ml. tubes.
c) 8x15 ml. tubes.
OPTIONALS : (Extra Cost)
Automatic 0-60 minutes timer.

MEDICO/CLINICAL CENTRIFUGE 6818
Electrically operated, Rectangular body sturdy, stable heavy body with resiliently mounted motor working on 220 Volts, 50Hz, single phase AC for vibration free performance with built in 5 speed regulator and a non-removable swing out rotor. Complete with tube carriers. Maximum speed 3500 RPM. Neatly finished in stoving enamel paint.
a) 4x15 ml. tubes.
b) 6x15 ml. tubes.
c) 8x15 ml. tubes.
OPTIONALS : (Extra Cost)
Automatic 0-60 minutes timer.

MEDICO/CLINICAL CENTRIFUGE 6819
As above but with conical body

VACUUM PUMP 6824
Motor driven, oil sealed pump mounted on heavy base. It is driven by V-belt at speed up to 400 RPM. Choice of single and double stage available creating ultimate vacuum of 0.01 mm of high column and 0.00mm of Hg column respectively. The pump is to work on 220Volts, 50Hz, single phase AC. Capacity Lt./minute x Motor HP
a) 25 x 0.25
b) 50 x 0.25
c) 75 x 0.25
d) 100 x 0.50
OPTIONALS : (Extra Cost)
Vacuum gauge, Belt Guard, Moisture trap, Non-return valve and Air blast.

SOXHLET EXTRACTION UNITS (MANTLE TYPE) 6830
Standard mild steel study body and upright fitting. Body finished in stove heating paint and other parts duly chrome plated. Housing provided with heating mantles for surface temp. up to 300ºC. Provided individual on-off switches & pilot lamps, without glass parts.
1) A unit of 3 mantles rating 500 watts.
2) A unit of 6 mantles rating 750 watts.

SOXHLET EXTRACTION UNITS (Heater type) 6832
Heaters have individual on-off switch & indicators. Provided with one common energy regulator to control all units. Without glass parts.
1) A unit of 3 heaters.
2) A unit of 6 heaters.

SOXHLET EXTRACTION UNITS (Hot plate type) 6833
As above but with hot plates.
1) A unit of 3 hot plates.
2) A unit of 6 hot plates.

SOXHLET EXTRACTION UNITS (Bath type) 6836
I. Single wall, chamber made of stainless steel. Provided with individual on-off switches but having one energy regulator to control all units. Units without glass parts.
1) A unit of 3 baths.
2) A unit of 6 baths.
II. Double wall, inner chamber made of stainless steel, other specification as above.
OPTIONAL : (Extra cost) Regulator can be provided against extra cost for all above units.
All above units work on 220 Volt AC 50Hz single phase.

KJELDHAL UNITS 6840
Made out of mild steel duly finished in stoving enamel paint. Other metallic parts are chrome plated. Following units are available.

a) KJELDHAL DIGESTION UNITS
Useful for estimation of nitrogen contents in substance by digestion in 300 & 500 ml flasks. Provided (optional) with fume duct made of lead and pair of hangers. To work on 220Volts, AC 50Hz, single phase. Individual on-off switches
and one energy controller for all units is provided.
1. Unit of 3 tests (Heater type)
2. Unit of 6 tests (Heater type)
3. Unit of 3 tests (Mantle type)
4. Unit of 6 tests (Mantle type)
OPTIONALS: (Extra Cost)
i) Fume duct made of lead or Borosilicate glass.
ii) Energy regulator.

b) KJELDHAL DISTILLATION UNITS
Asbestos tops mounted on mild steel tubular stand. Provided with condenser clamps and water manifold. Other specification as above.
1. Unit of 3 tests (Heater type)
2. Unit of 6 tests (Heater type)
3. Unit of 3 tests (Mantle type)
4. Unit of 6 tests (Mantle type)
OPTIONALS: (Extra Cost) Energy regulator.

c) KJELDHAL DISTILLATION & DIGESTION UNITS (Combined)
One single mild steel tubular stand is provided with two heating shelves, one above the other. A fume duct holder and a heating box are supplied for digestion unit. The heating units have individual on-off switches. In the upper portion another heating unit with a condenser rack is provided. the unit is workable on 220Volts 50Hz, Single phase AC. Complete with cord & plug etc.
1. Unit of 3 tests (Heater type)
2. Unit of 6 tests (Heater type)
3. Unit of 3 tests (Mantle type)
4. Unit of 6 tests (Mantle type)
OPTIONALS: (Extra Cost) Fume duct made of lead or Borosilicate glass. Sunvic energy regulator. Note : All above units are without glass parts.

AUTOCLAVE LABORATORY (PORTABLE) 6843
Suitable for general laboratory use and sterilization. Stainless steel or aluminium vertical body having no joints. Pressure range 15psi to 18psi. Domed cover can be sealed by a joint less gasket which is clamped to the vessel by wing nuts by hinged bolts which engage slotted lugs on rim of the cover. Provided with dial pressure gauge. Spring loaded safety valve has threaded cap for pressure adjustments. Supplied complete with plug & cord and is suitable to work on 220 V AC 50 Hz single phase.
Sizes :Dia x height in mm:
a) 300 x300
b) 300 x 375

AUTOCLAVE (Vertical) 6845
A versatile, electrically heated sterilizer under saturated steam of adjustable pressure of 10 to 20 psi. Double walled construction with boiler & steam jacket made of thick stainless steel and gap is filled with high grade glass wool to bring the temperature loss to a minimal level. The outer chamber is made out of thick mild steel. The lid is made of thick stainless steel plate (joint less) or gunmetal plate and can be sealed by a joint less neoprene rubber gasket by wing nuts through hinged bolts by engaging slotted lugs on rim of the cover. Provided with dial pressure gauge, air/steam release cock., spring loaded safety valve adjustable to any required point from 10 psi to 20 psi with accuracy ± 3 psi. A drain cock has also been provided. a double safety valve has also been provided along with water inlet. Supplied complete but without dressing bins. Chamber Size mm - Load
a) 250x450 - 1.5 KW
b) 300x500 - 2.0 KW
c) 350x450 - 3.0 KW
d) 400x600 - 4.0 KW
e) 450x600 - 4.0 KW
f) 550x750 - 5.0 KW
OPTIONALS : (Extra Cost)
i) Automatic low-water level cut-off device
ii) Pressure control switch
iii) Radial lock (for models d, e & f only)
iv) Dressing bins for various sizes (rates on request.)
v) Water level arrangement.

AUTOCLAVE (Horizontal) 6846
Specification as in vertical model but presented in a horizontal position and without steam jacket. The outer body made of mild steel , inner chamber made of stainless steel. Chamber Size mm x Load
a) 350x550 x 4KW
b) 450x600 x 6 KW
c) 550x750 x 6 KW
d) 400x1100 x 9 KW
OPTIONALS : (Extra Cost)
i) Pressure Gauge ii)Automatic low water level cut-off device. iii)Pressure control switch.

AUTOCLAVE FUMIGATOR 6847
Autoclave Fumigator is a Multi purpose product in the Hospital. It acts as Disinfector, Humidifier, Clematises, Insect Repellant Sprayer and Atomiser in the Hospital Fumigator Concentration is as below For routine disinfection, 30ml of formaline of 40% concentration with 90ml of pure water is 1000 Cu ft Area. For Intensive disinfection, 90ml of formaline of 40% concentration with 90ml of pure water is sufficient for 1000 Cu ft Area. Formalin : Dettol, Savlon, Servocide, Phenol can be safely used. This fumigator is best suited for Hospitals and related Industries.

SEED GERMINATOR (Single Chamber) 6850
a) Specification as above with chamber of anodized aluminium chamber. Size: 555 (W) x 910 (H) x 605 (D) mm.
b) As above but chamber of stainless steel.

SEED GERMINATOR (Dual Chamber) 6852
Specification as above but double chamber. For cooling a sealed compressor unit has been provided below the chamber to work independently. Each chamber size : 555x910x605mm
a) Heating and cooling in separate chambers: Chamber made of anodized aluminium.
b)As in (a) but chamber made of stainless steel.
c)Heating & cooling in both chamber and chambers made of anodized aluminium.
d) As in (c) but chambers made of stainless steel.
OPTIONALS: (Extra Cost) i) Automatic 0-24 hours timer to regulate cyclic illumination conditions. ii) Automatic voltage stabilizer - 3KVA (must)

HUMIDITY CABINET 6855
Double walled construction, inner made out of richly anodized aluminium or stainless steel sheet and outer that of thick mild steel duly finished in stoving enamel paint. Gap is filled with glass wool for temperature, insulation. A circulation fan has been provided to maintain uniform temperature & humidity through out the chamber. Nichrome heating elements are provided to heat the chamber effectively. Temperature range from ambient to 60ºC is controlled by a thermostat. L-shaped thermometer is provided to indicate temperature in the chamber. Humidity is created by a generating steam by heating water in a stainless steel reservoir by an immersion heater and subsequent condensation in circulating air. the humidity is controlled by a humidistant from atmospheric humidity to 95% ±3% RH. The double walled door has bee n provided with a double wall clear glass window for observation in the chamber without opening the door and disturbing chamber conditions. A control panel has been provided on left of the body and is provided with all control switches phase. Supplied complete with cord & plug but without hygrometer.
OPTIONAL : (Extra Cost): i)Hygrometer (Humidity indicator), ii) Digital temperature Controller-cum-Indicator, iii) Digital temperature indicator, iv) Automatic voltage stabilizer 3 KVA.
Models: Chamber size :
a) 455 x 455x 455 mm. (Ht.)
b) 455 x 455x710 mm. (Ht.)
c) 605 x 605x605 mm. (Ht.)
d) 605 x 604x 910 mm. (Ht.)

HUMIDITY CABINET (TEMPERATURE CONTROL) 6856
Environmental Chamber, General specification as above but with added specification for low temperature control & humidity. The inner working chamber is made out of stainless steel. The temperature can be controlled from 5ºC-55ºC ±2ºC and humidity from 55% to 95% ±5% Rh through an electronic digital controller-cum-indicator. Temp. below ambient is controlled by hermetically sealed compressor complete with accessories heated by immersion heaters are provided to create humidity. Complete with all accessories. Control panel provided with control switches and indicators. The equipment to work on 220Volts, AC 50Hz, single phase. Provided with plug & cord but without hygrometer. Models: Chamber size in mm.
a) 455 x 455 x 710 mm. (Ht.)
c) 605 x 605 x 605 mm. (Ht.)
d) 605 x 605 x 910 mm. (Ht.)
OPTIONALS : (Extra Cost)
i) Digital type hygrometer (Humidity indicator)
ii) Automatic voltage stabilizer 3 KVA (must)

BLOOD BANK FREEZERS 6860
Standard double walled construction, inner chamber made out of stainless steel sheet and outer that of thick mild steel sheet duly stoving enamel painted and gap filled with glass wool for temperature insulation. Complete with double walled door with lock & key arrangement. Temperature between 4ºC to 6ºC is maintained by a digital temperature controller-cum-indicator and trigger audio-visual alarm in case of temperature fluctuations. A door operation alarm is also provided along with power failure alarm as a safety device. Drawers with index cards have been provided to hold blood bottles or blood bags. A sealed compressor unit and cooling coils running throughout the chamber are provided for thermal uniformity. Panel provided with pilot lamp, controls etc. Supplied with cord & plug etc. and equipment to work on 220 Volts, 50Hz, single phase AC. Models:
a) Capacity 140 bags or 70 bottles of 450 ml.
b) Capacity 210 bags or 100 bottles of 450 ml.

BLOOD BANK FREEZER (Economy Model) 6861
Specification as above but capacity 70 bags or 35 bottles and without door operation and temperature fluctuation alarms.
OPTIONAL : (Extra cost) Automatic voltage stabilizer 3KVA (must)
Note: Vaccine Freezers, Semen Freezers, Plate Freezers and Test Tube freezers are also offered on demand.

AUTOMATIONS DEEP FREEZER 6864
These plasma storage cabinets are designed for quick freezing and storing of plasma and related blood components at desired low temperatures up -35ºC. All models feature integrated control panel with digital temperature indicator cum controller and temperature recorder. Constructed of double walls, the exterior is made of powder coated sheet, steel finish while the inner chamber is made of stainless steel. The unit is mounted on castor wheels for ease of mobility. Plasma Freezers are available in horizontal and vertical versions. Temperature of Freezer also reduce up to -70ºC as per requirement. Special Features:
• Low temperature up-to -35ºC.
• Stainless Steel inner chamber
• Extremely efficient insulation to minimise heat loss.
• Digital temperature indicator cum controller with audio visual alarm.
• Inside acrylic door to avoid temperature loss.

PLATLET AGITATOR WITH INCUBATOR 6866
Stainless Steel bag holder of good quality to allow effective temperature and good quality ventilation of platelet bags, achieved by one piece drawers for complete air circulation on both surfaces of bags. Continued shaking of bags to prevent clogging (by side to side motion), ½" 4-5 RPM with heavy duty ball bearing gear motor and Internal fan.

BLOOD COLLECTION MONITOR 6870
Preprogrameble collective device to draw precise volume of blood from donor. Fitted with uniformly oscillating collection tray to agitate blood during collection and ensure uniformly mixing of blood anti coagulant. Oscillation speed: 10RPM. Digital display indication:
• The volume of blood in the blood bag during collection.
• Set volume, the volume which is to be collected.
• Flow of blood, i.e. normal, high or low and indicating buzzer to abnormal flow.
• Time taken for collection of set volume and running time also.
• Automatic termination of blood collection when blood volume collected reaches preset volume.
Pause function for temporary stopping of blood collection in process but at that time oscillation will be continuing.
• Battery operated model also available (Optional model)

DI-ELECTRIC TUBE SEALER 6872
• To seal tubing of plastic bags.
• To provide hermetic seals on plastic tubing containing blood without causing haemolysis.
• Plastic t6ubing sealed able to separate by pulling apart without leakage of blood.
• Oscillation frequency: 40.68Mhz.
• Maximum tube dia: 6mm
• I/P supply: 230Volt AC ±1%, 50Hz, single phase.
• Power consumption: 12VA.

LAMINAR AIR FLOW CABINETS (Horizontal) 6875
Laminar flow principle involves double filtration of air through coarse pre-filters (up to 5 microns) and Heat filter (down to 0.3 microns) for filtration of biological and particulate contaminants. A constant uni-directional air flow is drawn from atmosphere and passed through pre and heat filters on the work surface. Fabricated out of reinforced ply board which is clab in from out side in laminated sheet and inner exposed areas are finished in epoxy paint. Table top covered with non-glaring laminated sheet or stainless steel sheet (optional). Side panels are fixed and are made out of transparent acrylic sheet. The front door is folding type and made of thick acrylic sheet. (Optional) Stand is built in type or detachable. Blower unit has AU or equivalent motor and is dynamically balanced with minimal sound & vibration level. Fluorescent lighting is also provided. A suitable UV tube is provided for sterilization. An acrylic block type manometer to measure static pressure in the chamber has been installed. Two way gas tap for gas line has also been provided. Working chamber sizes in mm.
a) 600x600x600 mm)
b) 900x600x600 mm)
c) 1200x600x600 mm)
d) 1800x600x600 mm)
OPTIONALS : (Extra Cost)
i) Stainless steel table top.
ii) Folding front door made of acrylic sheet.

LAMINAR AIR FLOW CABINETS (Vertical) 6876
As above but Vertical Module

PLANT GROWTH CHAMBER 6878
Useful to conduct experiments on plant growth in controlled environmental conditions. Double wall construction, inner made of anodized aluminium or stainless steel sheet and outer made of thick mild steel sheet duly finished in stoving enamel paint. the gap is filled with glass wool for insulation of temperature. In addition to a double walled door a full view clear acrylic door is provided for observation in chamber without opening it to avoid disturbance to the inner conditions. Instead a double glass window can be provided in the main door. Adjustable perforated shelves of stainless steel are provided. Temperature range 5ºC to 50ºC ±1ºC is controlled and indicated by a dual electronic digital temperature controller-cum-indicator. Humidity control from 55% to 95% ±2%RH is attained by a humidistant and created in a stainless steel water reservoir set below the chamber and heated by immersion heater. A 0-24 hour timer is also provided. The control panel is provided with indicator lamps, controls etc. Equipment to work on 220Volts, AC 50Hz, single phase. Supplied with cord & plug. Arrangement for fluorescent illumination and daylight has also been provided. The control panel is provided with indicator with indicator lamps, controls etc. Equipment to work on 220Volts, 50Hz, AC single phase. Supplied with cord & plug. arrangement for fluorescent illumination and daylight has also been provided.
Chamber size x Capacity:
a) 570x875 x 550 mm. x 10 Cft.
b) 775 x900 x 775 mm. x 20 Cft.
c) 825 x1200x 825 mm. x 30 Cft.
d) 900x1720x800 mm. x 45 Cft.
OPTIONAL : (Extra cost) Automatic voltage stabilizer 3 KVA (must)

MORTUARY CHAMBER 6940
Designed to store cadaverous under cool conditions to prevent decomposition. Double walled construction, outer made out thick mild steel sheet duly finished in stoving enamel paint and inner made out of stainless steel sheet. the gap between the two is filled with glass wool for temperature insulation. Front opening covered with double walled door with magnetic gasket, lock & key and handle. Individual chambers are provided with independent locks with duplicate keys, Trays to carry dead bodies are provided with handles on both ends travel on rollers fitted on ball bearings for smooth movements. The refrigeration unit is fitted on the rear top. Temperature of -20ºC to 4ºC is maintained by hermetically seated compressor unit and is controlled by an automatic electronic digital temperature controller-cum-indicator. Panel is provided with indicators & controllers etc. Complete with cord & plug. The unit work on 220Volts, 50Hz AC single phase. Models :
a) Single Body
b) Two bodies
c) Three bodies
OPTIONALS: (Extra Cost)
i) Outer made of stainless steel sheet
ii) Automatic voltage stabilizer 3KVA

DESTRUCTOR INCINERATOR 6954
Developed as per standard guide lines provided by Central Pollution Control Board.
The Incinerator is a twin chamber unit, externally built with a strong M.S. casing which houses special refractory bricks. The inner lining of the chambers is gilded with high alumina refractory bricks. Additional insulation bricks with ceramic fibers are provided all around the refractory lining. The inner most lining is of siliminite grooved bricks.

Both the Primary and Secondary Chamber are installed with nickel chromium heating coils to maintain the required temperatures. Heating coils are located in completely closed grooved bricks and terminated in the terminal box at the rear. The charging door is in the front of the unit. The Primary and secondary chambers are one above the other and the flue gases after burning the waste, are drawn out from the side of the incinerator unit. Each of the chambers is provided with a pair of temperature sensors and connected to the control panel. Ash is collected in a tray from the rear bottom. The Incinerator System comprises of the following main equipments:

1. Main Incinerator Unit - As described above.

2. Electric Control Panel - The 3 phase power supply is connected to the main incomer of the control panel. As isolator switch is provided at the incomer. Separate feeder are provided for the heaters of the chamber and blowers. Push button ON/OFF switches and indication lamps are provided. The temperature indicating controllers of both the chambers are also provided in the control panel. Ammeter and Volt meter with selector switches are provides. The temperature indicating controllers are digital type to indicate the prevailing temperature in the chambers and also cut off the heaters when the preset temperature is attained.

3. Air Blower - The air blower ensures supply of adequate air for combustion of the waste materials. The blower is driven with directly coupled motor (3 phase 415 Volts 50 Hz.) A butterfly valve is also provided for operational control.

4. Exhaust Fan - The exhaust fan ensures necessary draught for drawing the flue gases from the system. The fan is driven through a belt and motor (3 phase 415 Volts 50 Hz.) A butterfly valve is also provided for operational control.

5. Cyclone Separator - Cyclone Separator is provided for gas cleaning. Cyclone Separator is fitted to the incinerator main unit after butterfly valve.

6. Chimney & Ductings - A chimney of up-to 30 Mtrs. height is provided to let out the flue gases in-to the atmosphere. The Chimney is fitted with a conical base bottom. A main hole at the bottom, sampling ports are provided to the chimney.

7. Water Filter

• Erection & commissioning charges of various models are extra.
• Universally replaceable spares and components are readily available on demand.