OSCILLOSCOPE 2530
The 20 MHz Dual Trace Oscilloscope is a compact, low line and lightweight
instrument. It’s high class engineering and rugged design ensures
very reliable performance. This is a general purpose Dual Trace Oscilloscope
having both Vertical amplifiers
offering a bandwidth of DC 20 MHz and a maximum sensitivity of 2mV/cm. Stable
triggering for low level signals is obtained upto 30MHz. Full X-Y operation
is achieved by switching Channel11 into horizontal deflection system so
that matched
sensitivities for both X and Y signals. A component tester is incorporated
in the oscilloscope which gives a quick test of both active and passive
components.
In addition Z-modulation facility is also provided. The fully stabilized internal
power supplies ensure reliable operation under adverse mains supply conditions.
The carefully selected components and Burn-in-tests ensure trouble free working
in most demanding environments. The 2530 offers five separate Add-on Modules
(optional) viz
• Frequency Counter
• Curve Tracer
• Power Supply
• Function Generator
• Digital Voltmeter.
OPERATING MODES
Channel 1, Channel 11, Channel 1 & 11 Alternate or chopped (approx. 120
KHz)
X-Y (Ratio 1:1 Input via CH 11), Add/Sub, Invert CH 11.
Vertical deflection (y)
(Identical channels)
Bandwidth: DC-20 MHz (-3dB), DC-28MHz (-6dB)
Risetime: 17.5 ns (approx.)
Deflection coefficients :
12 calibrated steps 2mV/cm - 10V/cm (1-2-5 sequence)
Accuracy: 3%
Input Impedance: 1 MW II 25 pF
Input coupling : DC-AC-GND
Input voltage : Max. 400 V (DC + Peak AC)
TIMEBASE
Time coefficients : 18 calibrated steps, 0.5 us/cm-0.2 s/cm (1-2-5 sequence)
with magnifier x 5 to 100 ns/cm, with variable control to 40 ns/cm.
Accuracy : 3% (in cal position)
Ramp Output : 5V (approx) TRIGGER SYSTEM
Modes : automatic or variable trigger level
Source : Ch I, Ch II, ALT, Line, Ext.
Slope : Positive or Negative
Coupling : AC, TV Frame
Sensitivity : int 5 mm., ext 0.8 V (approx.)
Trigger Bandwidth : 40 MHz HORIZONTAL DEFLECTION (x)
Bandwidth: DC-2.3 MHz (-3 dB)
X-Y mode: Phase Shift < 3º at 60 KHz.
Deflection coefficients: 12 calibrated steps 2mV/cm 10V/cm (1-2-5 sequence)
Input Impedance: 1 MWII 25 pF.
COMPONENT TESTER
Test Voltage : Max 8.6 V (Open)
Test Current: Max 8mA (Shorted)
Test Frequency: 50Hz, Test circuit grounded to chassis
Continuity Tester: Beeper sounds <75W approx.
GENERAL INFORMATION
Cathode Ray Tube: Rectangular medium short persistence (P31)
Accelerating potential: 2000 V
Display: 8 x 10 cm
Trace rotation : Adjustable on front panel
Calibrator: Squarewave generator 1 KHz (approx) 0.2 V ±1% for probe
compensation.
Z Modulation: TTL level Stabilized
Power Supply: All operating voltages including the EHT.
Mains voltage: 220 V -240 V, 50 Hz. (Switch at back)
Mains fluctuations: 10% (max.)
Power Consumption: 33 VA (Approx.)
Weight (approx): 7.5 Kg.
Dimensions (mm): W285-H145-D380
Operating Temperature: 0-40º, 95% RH
Finish: Off white with handle and tilt stand.
OSCILLOSCOPE Demonstrator Cum Trainer 3028
Oscilloscope Demonstrator Trainer is specifically designed for the study of
working of an Oscilloscope. It is a user friendly fully working oscilloscope
in an open form. The controls are placed actually at the place as they are
in the circuit schematic. Thus a trainee can locate any section, components
of the section and can study it thoroughly. the function controls and adjustment
controls are fully adjustable to the trainee to verify their effect on the
working of the scope. An illustrated Block and Circuit Schematic and the
adjustment plan right in front of trainee’s eyes helps him to co-relate
each operation during the demonstration.
Also Available:
Function Generators: 1 MHz, 2 MHz, 3 MHz
Antenna Trainers
Transmission Line Trainer
Fiber Optics Trainers
Basic Fiber Optics Trainers
Advanced Fiber Optics Trainers
Laser Fiber Optics Trainers
Optical Power Meter
Temperature Transducer Trainers
Microprocessor Kits
Micro Controller Trainer kit Interfacing Modules for Microprocessor kits
Data Acquisition Card and Digital
Analog IC Tester
PC Demonstrator
|